- #Vinylmaster pro graphtec fc8600 how to#
- #Vinylmaster pro graphtec fc8600 install#
- #Vinylmaster pro graphtec fc8600 drivers#
- #Vinylmaster pro graphtec fc8600 driver#
- #Vinylmaster pro graphtec fc8600 full#
Hi, I am having the same issue with code I downloaded the latest driver from Graphtec and the cutting plotter software shows in my programs.Discussion in ' Graphtec ' started by ReynaWrapsNov 6, Welcome To Signs This site uses cookies. If that does not help contact Graphtec for support. Factory reset? Hold down UP Arrow while turning power to cutter on? Reboot computer before reinstalling. What are you doing prior to the code? You just turned your cutter on and the code is there? And which software are you using? Have you done all of these.
#Vinylmaster pro graphtec fc8600 drivers#
Many thanks for that, yes we are running the new drivers We have no idea what you are doing, before you are getting this code.
#Vinylmaster pro graphtec fc8600 full#
Win 10 is still new and full of surprises.
#Vinylmaster pro graphtec fc8600 install#
Graphtec contour cut issuesĪny thoughts? I usually use Vinyl Master - Now Ive got it set up okay with reference to pressure etc the only thing I have noticed is on circles Im getting straight lines in the curve Any thoughts? Did you download and install the latest driver from graphtec? That could help. I had a run of 2k to do, after batching out a 5'x8' section of them and having issues, I just opted for 5'x1' groups, and set the plotter up to read the next set.A couple of things when I try to open the Cutting Plotter Controller I get the following error "No compatible Driver has been found - Code " but if I open up the Graphtec Studio it finds the cutter and communicates fine with it. We had this issue when cutting large numbers of bumper stickers for a client on our FC, we turned the print so that they are cut with the longer side of the image on the vertical y-axis, and this worked for us. Spot on - tried using segments vs 4 points with no segment marks. I have a Graphtec FC Having issues with the contour feature cutting accurately as it cuts multiple stickers.įirst few cuts great then the cuts tend to move up y axis. Emailed Graphtec support, no reply yet to my inquiry.
#Vinylmaster pro graphtec fc8600 how to#
I have a Summa d that is very finicky and over 8 years I have learnt how to deal with it.Discussion in ' Graphtec ' started by ReynaWrapsNov 6, Welcome To Signs This site uses cookies.īy continuing to use this site, you are agreeing to our use of cookies. I would reset computer and plotter and I would try to recreate the cut file could be something wrong with the file itself then resend and see what happens. This can also throw off your mark layout if you have different settings for each. The cut file will still have the plotter looking for the segmented ones. If you send to RIP and then change the reg type from there the cut file will still think they are the original style. Except when you first hit print make sure that you are set to the correct registration marks. What firmware is the cutter running? I would start by upgrading that Mar 31, 4.Īnd then you went through the steps of actually resetting it and putting it back to the correct language right? If you did I don't have much for you. I typically blame it on production manager because it seems as if a job sits a few days in PM I fight getting it to read marks Mar 31, 3. Currently at X70 - Y80 Is there some magical solution that I'm just missing? Mar 31, 2. Nothing I've tried will make it find the registration marks. Finished one job, loaded the next same material, same laminateand it's never worked again. We have an FC that was working perfectly. By continuing to use this site, you are agreeing to our use of cookies.
Abnormal noise generated by the cutter pen during cutting.Discussion in ' Graphtec ' started by Pat WhatleyMar 31, Welcome To Signs This site uses cookies. The medium gets entangled during cutting. The medium can be cut but is hard to weed afterward. Use a cutter blade that matches the plunger's diameter. The cutter blade is the incorrect diameter for the plunger. The cutter blade falls out of the cutter plunger. The cutter blade is cutting into the backing sheet. The cutting medium peels away from the backing sheet when cutting small characters. The cutting medium curls up at the corners. Slight skipping of the blade The cutter blade is extended too far.Īdjust the blade length. Solid lines are not cut at a constant depth. Remove any foreign matter inside the holder. The cutter blade does not rotate smoothly.
Match the setting to the blade being used. Symptom Cause Solution The cut corners are rounded or too pointed.
0 kommentar(er)
